The photo is in the can, but it is the post-processing that decides whether a product looks high-quality in a catalog or on a website. That is exactly what Maik's tutorial from the series "Getting Started with Product Photography" is about. The video runs just under six minutes and uses four examples to show how small corrections subtly enhance a subject without making it look artificial. You will see a combination wrench, a sports shoe, a wine glass, and a cordless drill, each from the original photo to the finished result.
Key Takeaways
- Post-processing should support the product, not distort it. Small interventions are usually enough.
- A RAW development forms the foundation: contrast, saturation, and sharpening can be adjusted there in a targeted way.
- Cut-out products can be presented against white, black, or a colored background, depending on the client's wishes.
- Individual shots can be combined into a coherent image, for example to distribute sharpness across the entire shoe.
- Retouching deliberately stays brief. You remove dust, edges, and spots in a targeted way, while the product itself remains unchanged.
- A crop, for example a square format, gives the image a new effect and opens up other possible uses.
Step-by-Step Guide
Step 1: Understanding the Starting Point with the Combination Wrench
Start by taking a look at the unedited product. The combination wrench is an elongated metal tool with an open-end side and a ring side, each for nuts. This shape is ideal for checking whether light and sharpness are evenly distributed before you begin editing. Pay particular attention to highlights and edges, because that is exactly where imperfections become noticeable later.

Step 2: Adjusting the Development for Contrast, Saturation, and Grain
Open the photo in your development software, for example Capture One, and adjust the contrast slightly so that the metal structure looks more three-dimensional. Then reduce the saturation a little so that the tool stays natural. In this example, you leave the grain unchanged. The difference is clearly visible when compared with the original, without the image looking exaggerated.

Step 3: Cutting Out the Product
For many shops, a cleanly cut-out background is mandatory. Maik shows two variants for this. The first is pure white, which is especially common for online shops. The second is black, which is very well suited to dark, dramatic moods. Since the product was photographed in front of a glass plate, the edges and borders can easily be cleanly isolated. This very advantage makes the technique so flexible.

Step 4: Setting a Colored Background and Changing the Color
If your client wants a colored background, you place the color area behind the cut-out product. With a spot, you can additionally direct light specifically onto certain areas. If the client wants a different product color, you open the color control and adjust the hue in a targeted way. In the example, Maik desaturated the entire color a little. This looks deliberately restrained in the video and shows how quickly a color change can be implemented.

Step 5: Combining the Sports Shoe from Two Shots
With the sports shoe, the sharpness in the original image lies only on the rear shoe. That is why two individual photos were taken, one with sharpness on the front shoe and one with sharpness on the rear shoe. You copy these photos together cleanly in the image editing software. Make sure that the position, angle, and light of the two shots match, otherwise you will clearly see the transitions later.

Step 6: Removing Dust and Distractions at the Corners
There was still some dust on the table, which is visible in the original image. Remove it with retouching by covering the distracting spots at the top left and right. Work with small brush sizes and check the results at high magnification so that no smeared areas appear.

Step 7: Subtly Darken the Tip of the Shoe
A small retouch follows in the front area of the shoe tip. The area is slightly darkened there to draw the viewer's eye to the essentials. Proceed carefully with the dodge tool or a soft mask so that the transition remains invisible. The result is a cover image that can be presented excellently in sales.

Step 8: Examine the Original of the Wine Glass
Before you work on the wine glass, you should look closely at the original photo. Only then will you recognize which areas really need to be corrected. Pay attention to the edges of the glass and to the frame that was used for brightening. These spots are crucial later for the fine-tuning.

Step 9: Perform the RAW Development of the Wine Glass
The development in Capture One is the most important step for this subject. You can see that the edges on the left and right stand out much more clearly and run all the way down to the base. You can control this effect specifically through contrast and sharpening. Proceed carefully so that the glass does not look harsh or unnatural.

Step 10: Transfer Edges and Remove the Frame
In the next step, you copy the side of the glass from the right side to the left so that the shape becomes even. Then you remove the frame that was used for brightening. To get the image composition right, you place the glass in the center of the image. Adjusting the crop additionally supports this effect.

Step 11: Develop the Cordless Screwdriver and Deliberately Shape the Look
For the cordless screwdriver, which was photographed with LED light, a strong development is worthwhile. Increase contrast and sharpening significantly until the surfaces of the tool really stand out. The results do look quite extreme, but that is exactly what suits the technical character of the product. Keep an eye on whether individual areas fray or look overdone.

Step 12: Carry Out the Retouching on the Cordless Screwdriver
In the retouching area, you remove the dust completely and add a spot in the upper area. The retouching should not replace the product's effect, but only round it off. Work step by step and keep checking the result against the original.

Step 13: Crop the Image to a Square
Finally, Maik decides on a square format. This crop looks simple and offers a completely different presentation than the original image. It is excellently suited for social media, catalogs, or tiles in online shops. Make sure to position the product so that nothing important is cut off even in the tighter crop.

Step 14: Deliberately Hold Back on the Retouching
At the end of the tutorial, Maik emphasizes that the retouching was deliberately kept brief. The focus is on light and composition; the post-processing serves only for fine-tuning. Stick to this principle in your own projects, because an overworked product quickly looks unbelievable.

Summary ??? Product Photography: Post-Production with Subtle Corrections
Post-production is not a substitute for good lighting, but its extension. You have seen that development, masking, color adjustment, retouching, and cropping are each only small steps, but together they have a great effect. What matters is to work with a sense of proportion and to always keep the product at the center.
FAQ
Which software is used in the tutorial for RAW development?The video uses Capture One, with which the RAW files are developed and contrast and sharpening are adjusted.
Why are two individual photos needed for the sports shoe?Since the focus in the original image lies only on the rear shoe, two shots with different focus areas are combined so that both shoes are shown in sharp focus.
Can I also cut out a product against a black background?Yes, according to Maik this works wonderfully, since with this technique the shot is taken in front of a glass plate and the edges can be separated cleanly.
How can I change the color of a product for a client?The hue can be specifically changed using the color slider, so a simple color change is possible quickly and easily.
